MIX & Plugins
STM STATION — hardware rack on the studio desk

STM STATION

Finish the channel and move on

A ready chain on one insert: filter, EQ, compressor, color, space, safety. Calm defaults, extra modules off. Fine on a first mix, and fine when you want the chain ready on every track.

Back

Live UI

Turn the knobs right here

Sense → Filter → EQ → Comp → Color → Space → Safe. Defaults: TRACK, PRE, CLEAN, Comp Amount at 0, OPEN EQ with cuts at 40 Hz / 19 kHz. The AU is already in the AnDUB chain.

$43 · €40

In catalog

What it is

One insert, the usual mix order

Precise EQ — open EQ. A hard limit — LIMIT. Six mix stages — Mixing Steps. STM STATION runs the whole channel on one insert: filter, equalizer, compressor, color, space, and safety, in one window.

A new mix is easier to keep intact. With some experience you finish a track, a group, or a master and move on.

1
Sense

Listen first: VU + TRIM. Same job as the SENSE floor in Mixing Steps.

2
Filter

First process: HPF / LPF on the input.

3
EQ

LOW/HIGH on the strip. OPEN EQ is 8 bands with a spectrum. Default: HP 40 Hz + LP 19 kHz.

4
Comp

AMOUNT starts at zero. Turn right for compression. CLEAN / FAST / SMOOTH + MIX.

5
Color

One character: SAT or Tape or Push.

6
Space

Local Delay or Reverb. Default OFF.

7
Safe

CLIP / LIMIT + CEILING at the end of the chain. Harder on Master.

Order is fixed: Sense → Filter → EQ → Comp → Color → Space → Safe. Sense always has the meter. Almost everything else stays OFF until you turn it on. Track / Group / Master change the defaults. The layout stays the same.

Why

What you get

Fewer windows. Fewer “what goes where” calls. Calm defaults and modules that start off. Precise EQ opens on its own. The station strip stays readable.

A small fixed kit in the DAW: you listen. Station is for a producer or a writer who mixes their own tracks. An engineer can run one logic across forty channels and save time.

  • One familiar layout on a track, a group, or the master
  • A fixed chain on every channel
  • Few knobs on the strip. Precision is in the OPEN EQ window.
  • AnDUB line: the sound you already know from the single AUs

When to pick it

When Station is the one to load

Situation What to load
Empty channel, a calm place to start STM STATION
Mix the whole track on one insert STM STATION
Just rumble, just a limiter, or just saturation A single plugin
A full pass through the AnDUB stages MIXING STEPS
Master: a fast, safe finish Station · Master, or LIMIT on its own
A one-off chain for a vocal, or a full engineering pass Separate plugins

Unsure what to load — Station. One clear job — a single plugin.

Two tools

STM STATION and MIXING STEPS

MIXING STEPS is a ready rack of 6 stages: SENSE → TONE → DENSITY → GLUE → PLACE → SPACE. A track mix by AnDUB stages: level, tone, density, tape, place in the stereo field, air.

STM STATION is a channel station. It starts the same way: Sense first (meter and trim), then Filter → EQ → Comp → Color → Space → Safe. Station covers more of a full mix. Mixing Steps goes deeper in the six stages.

MIXING STEPS STM STATION
What it is Rack of mix stages Channel / group / master station
Path SENSE→TONE→DENSITY→GLUE→PLACE→SPACE Sense→Filter→EQ→Comp→Color→Space→Safe
Strength Walks you through the stages Most of the daily chain on one insert
Comp Density / Glue stages CLEAN / FAST / SMOOTH on board
Ceiling Ceil / clip inside Density Safe at the end of the chain
When to load I want to mix by AnDUB stages I want one desk on the channel

Sense on the strip is a meter and trim. Mixing Steps keeps the full six-stage rack as its own product.

MIXING STEPS page

Ecosystem

The desk, plus the precision tools

EQ, COMP, SAT, LIMIT, TAPE, CLIP, reverb/delay, and Mixing Steps stay in the line. They cover one job at full depth. Station is how you mix a whole channel when you want one familiar order.

A large hall works well as a DAW send. Space in Station is a short depth on the channel.

STM STATION is the everyday channel desk: a clear order and calm defaults. Single jobs go to EQ, LIMIT, and the other AUs.

Manual

How to use STM STATION

Working order of the station: roles, the module chain, a 5-minute recipe, and answers to common questions. The page has a spoiler. The full text is in the PDF too.

Download PDF STM-STATION-manual.pdf · AnDUB by STM

Open the manual on this page

1. What it is

STM STATION is a channel desk on one insert: a fixed, safe mix order with few knobs on the strip.

  • EQ, COMP, SAT, LIMIT, and the other AUs — when the job is one precise move.
  • MIXING STEPS — six mix stages.
  • STATION — the everyday desk: a track, a group, or the master on one insert.

Tip. Unsure what to load — take Station. One clear job — a single plugin.

2. Where to put it — Track / Group / Master

The three buttons on the left set the instance role. One role is selected. The panel looks the same. Aggression defaults change.

RoleWhereWhat changes
TRACKA normal channelCalm defaults, softer Safe
GROUPA bus / groupA bit harder glue and ceiling
MASTERStereo master (2-bus)Safe and the ceiling sit harder

3. Chain order

Sense → Filter → EQ → Comp → Color → Space → Safe

The order is fixed. Modules stay in place. Sense always has the meter. Everything else starts OFF until you turn it on.

4. Modules

Sense — listen first

  • VU is the analog signal level.
  • TRIM is the input level.
  • PRE ↔ POST is the toggle under the VU: PRE is before the Station chain, POST is after the processing.
  • LF / MID / HF is a quick tone balance on the input.

Tip. Sense first (VU in the live zone), then Filter and on down the chain.

Filter — first process

HPF cuts rumble and extra low end. LPF takes off the harsh top. Filter is the first process on the channel. Sense handles listening and level.

EQ — fast tone and OPEN EQ

On the strip: LOW and HIGH (shelves). The OPEN EQ button opens a window with the curve, a spectrum, and 8 nodes, the same window as STM EQ. Factory default: HP 40 Hz on the left and LP 19 kHz on the right. The middle is flat. Click empty space to add a Bell, drag X/Y, double-click removes the band.

Comp — glue

  • AMOUNT starts at 0 (bypass). Turn it right and compression comes in.
  • MIX is parallel dry/wet.
  • One mode: CLEAN / FAST / SMOOTH.

Color — one character

One character: SAT or TAPE or PUSH, plus the DRIVE knob.

Space — local depth

One AMOUNT. Type: DLY or RVB. Short insert on the channel. A big hall stays on a DAW send.

Safe — end of the chain

CEILING is the ceiling. CLIP / LIMIT is the protection mode. On MASTER, Safe stays in the chain. On TRACK, turn it on when the channel needs a ceiling.

5. A 5-minute working recipe

  1. Pick the role: TRACK / GROUP / MASTER.
  2. Sense: PRE + TRIM until the VU is alive and out of the red.
  3. Filter: HPF until the low end is clean. LPF when the top needs it.
  4. LOW / HIGH. Open OPEN EQ when you need a precise curve.
  5. Comp when the level is wandering.
  6. Color: one character, DRIVE kept modest.
  7. Space: DLY or RVB, AMOUNT barely audible. A big hall goes to a DAW send.
  8. Safe on the group or master. VU to POST, then check the level.

6. Station and Mixing Steps

MIXING STEPS is a rack of six floors. STATION is the channel desk with Comp, Color, and Safe. Sense here is the meter and trim. The full floor-by-floor pass lives in Mixing Steps.

7. Common questions

Can Delay and Reverb run together?
DLY or RVB, one at a time — the same switch as SAT / TAPE / PUSH in Color.

What is OPEN EQ for, next to LOW and HIGH?
The strip is for fast moves. The OPEN EQ window is the precise curve, and the station strip stays clear.

What does PRE / POST do?
The toggle under the VU picks the meter point: Station input, or the output after the chain.

Does Station cover every AnDUB plugin?
Station covers the everyday chain. The single AUs are there when you want to go deeper on one job.

8. About this manual

This manual is the working order for STM STATION: roles, the module chain, and the everyday mix recipe.

© AnDUB Plugins by STM

Buy

STM STATION is ready

The AU is already in the AnDUB line: put it on a track, a group, or the master and mix along the fixed chain. TRIAL is on the storefront. The full license comes after payment, key by e-mail.

Live UI Manual PDF MIXING STEPS