MIX & Plugins
CLIP — analog clipper on the studio desk

CLIP

Soft and hard clip, oversampled

CEILING · DRIVE · SOFTNESS. One insert on the bus.

Back

$54 · €50

In catalog

Demo

Hear the plugin at work

До

До обработки

Файлы будут загружены позже

После

После плагина

Файлы будут загружены позже

What it's for

The clipper cuts the shape of the wave

On a drum bus or the 2-bus you want the top of the wave under control: punch stays, peaks come down, the bus gets thicker, transients stay up. CLIP does that with oversampled soft/hard shaping.

CEILING Clip depth 0…−30 dBFS. Higher knob, lower threshold, thicker wave.
DRIVE Input gain up to +18 dB, plus an auto-pull of the ceiling by another 0…6 dB. More of the signal hits the curve.
SOFTNESS Knee of the soft curve: from a near-hard knee to a smooth rounding of the peaks.

Signal path

Oversample → drive → shape → (Δ) → OS ↓ → DC

The whole clip runs at a raised sample rate. HARD starts as a very steep power curve. The brickwall blends in only at full HARD. Less alias, and the edge stays hard.

CLIP signal chain IN OS×2 DRIVE SHAPE Δ? OS↓ DC? OUT
Δ and DC are options. The scope and the LED ladder show how much is clipping.

SOFT · HARD · DC · Δ

Four path modes

Button What it does When
SOFT Power soft-clip: x / (1+|x/t|^n)^(1/n), n comes from SOFTNESS Bus and vocal. Thickness, the top stays smooth.
HARD Steep knee (n≈22) into the brickwall; attack GR ~0.25 ms Drum bus, a hard master print
DC HP 15 Hz after the clip, removes the offset from the asymmetry On almost always (the default)
Δ Output = wet − dry: only what was cut Set ceiling/drive by ear, or as an FX layer

What's inside

Shape plus envelope GR

Ceiling + Drive

>CEILING 0…10 → 0…−30 dBFS. DRIVE adds gain ×1.8 dB · drive and pulls the threshold another drive × 0.6 dB. The effective ceiling shows on the scope as red dashes.

Envelope follow

>After the shape, instant GR is measured. Soft attack ~1 ms, Hard ~0.25 ms, release ~14 ms. Output = driven × smoothed GR. Transients stay click-free.

LED ladder

Seven lamps follow GR: the first at ~1.5% reduction, all seven at ~28%. A light soft-clip shows on the ladder.

CLIP SCOPE

>Peak-hold min/max per bin, CRT grid, ceiling lines. Turn CEILING or DRIVE and you see where the wave is cut.

Starting points

Don't turn DRIVE all the way up until you see the LEDs.

Job Mode CEILING DRIVE SOFTNESS DC / Δ
Drum bus, density SOFT 6–8 1.5–3 6–9 DC on
808 / bass print HARD 5–7 2–4 3–5 DC on
Vocal bus, peak control SOFT 4–6 1–2 7–10 DC on
2-bus, a light glue-clip SOFT 3–5 0.5–2 8–10 DC on
Hear only the clip any — — — Δ on

Δ = listen to the difference. Hear crunch — lower DRIVE or raise CEILING (less depth).

Wave shape

CLIP changes the wave shape

Brickwall limiter CLIP
Transient Lookahead + GR pulls the punch down The top of the wave changes. The body stays.
Alias Cheap limiters often skip oversampling 2× OS and a steep hard curve
Feedback A GR meter in dB Scope and 7 LEDs on the real clip amount
Clip A/B You guess by ear The Δ button plays only what was cut

Specs

Short version for manual readers

  • Format Mac Audio Unit · Standalone
  • DSP Stereo, 2× OS soft/hard power-clip
  • Ceiling 0…−30 dBFS + drive pull 0…6 dB
  • Drive 0…+18 dB input
  • Modes SOFT / HARD · DC HP 15 Hz · Δ diff
  • UI Scope + LED GR ladder · 700×297
  • Latency Oversampler only, no lookahead
  • Default Soft, ceiling 7, drive 2, softness 8, DC on

Put it on the drum bus. Watch the scope. Turn CEILING until 2–3 LEDs light.

Kick sits tighter. Peaks stay down. That's CLIP.